وظائف فني تعبئة و تغليف في الكويت

<p>Role &amp; Responsibilities We are seeking experienced Service Engineers, Senior Service Technicians, and Service Technicians for a leading Industrial Service Company in Kuwait specializing in compressed air systems. The candidate should have hands-on experience in maintenance, troubleshooting, overhaul, installation, commissioning, and repair of oil-injected rotary screw air compressors and compressed air dryers.</p><p>Compressor Brands Experience (Any One or More)</p><ul><li>Atlas Copco</li><li>Ingersoll Rand</li><li>Gardner Denver</li><li>Kaeser</li><li>Sullair</li><li>CompAir</li><li>ELGi</li><li>Chicago Pneumatic</li><li>Quincy</li><li>BOGE</li><li>Other internationally recognized industrial compressor brands</li></ul><p>Key Responsibilities</p><ul><li>Preventive and corrective maintenance of rotary screw air compressors.</li><li>Troubleshooting mechanical and electrical faults.</li><li>Major overhaul of compressor packages.</li><li>Airend inspection, repair, and replacement.</li><li>Bearing replacement and mechanical seal replacement.</li><li>Motor replacement and alignment.</li><li>Coupling alignment using dial indicators or laser alignment tools.</li><li>Maintenance of belt-drive and direct-drive compressor systems.</li><li>Oil system and cooling system servicing.</li><li>Replacement of oil separators, oil filters, and air filters.</li><li>Inlet valve, blowdown valve, minimum pressure valve, and thermostatic valve overhaul.</li><li>Solenoid valve troubleshooting and replacement.</li><li>Leak detection and repair.</li><li>Installation and commissioning of compressors after overhaul.</li><li>Performance testing and fault diagnosis.</li><li>Preparation of service reports and customer support documentation.</li></ul><p>Electrical Responsibilities</p><ul><li>Troubleshooting industrial electric motors.</li><li>Working knowledge of Star-Delta starters.</li><li>Experience with Soft Starters.</li><li>Experience with VFD/VSD drives.</li><li>Electrical control panel troubleshooting.</li><li>PLC and electronic compressor controller diagnostics.</li><li>Pressure and temperature sensor troubleshooting.</li><li>Reading and understanding electrical wiring diagrams.</li><li>Electrical fault diagnosis using multimeters and clamp meters.</li></ul><p>Air Dryer Experience</p><ul><li>Refrigerated Air Dryers.</li><li>Heatless Desiccant Dryers.</li><li>Heated Desiccant Dryers.</li><li>Automatic Condensate Drain Systems.</li><li>Air Filtration Systems.</li><li>Moisture Separators.</li><li>Dew Point Controllers.</li></ul><p>Tools Knowledge</p><p>Candidates should be familiar with :</p><ul><li>Dial Indicators</li><li>Laser Alignment Tools</li><li>Torque Wrenches</li><li>Bearing Pullers</li><li>Hydraulic Presses</li><li>Multimeters</li><li>Clamp Meters</li><li>Megger (Insulation Resistance Tester)</li><li>Pressure Gauges</li><li>Infrared Temperature Guns</li><li>Vibration Meters</li></ul><p>Other Requirements</p><ul><li>Good communication skills in English.</li><li>Ability to work independently at customer sites.</li><li>Strong troubleshooting skills.</li><li>Safety-conscious and team-oriented attitude.</li><li>Valid Passport preferred.</li><li>Ready to relocate to Kuwait.</li></ul><p><strong>Desired Candidate Profile</strong></p><h3>Preferred Candidate Profile</h3><p>Qualification</p><ul><li>ITI Mechanical / Electrical</li><li>Diploma in Mechanical Engineering</li><li>Diploma in Electrical Engineering</li><li>Equivalent Technical Qualification</li></ul><p>Experience</p><ul><li>3 to 15 years of relevant experience in industrial air compressor service and maintenance.</li><li>Hands-on field service experience is mandatory.</li><li>Experience in shutdowns, commissioning, and troubleshooting preferred.</li><li>Gulf experience will be an added advantage.</li></ul>

Workshop supervisor, Storekeeper, Rigger and fitter, Tyre ma<br><br> Job Id :100194479<br><br>Postjob service<br><br>×<br><br>Please enter details to report job<br><br>Name*<br><br>Email*<br><br>Reason to report<br><br>Description<br><br>WE ARE HIRING – URGENT REQUIREMENT (KUWAIT)<br><br>Oil & Gas Experience Required<br><br>???? Positions Open:<br><br>Workshop Supervisor (Maintenance department)<br><br>Storekeeper - Mud plant<br><br>Rigger & Fitter<br><br>Tire Man (Heavy Vehicles)<br><br>???? Key Points<br><br>✅ Oil & Gas industry experience mandatory 3-5 years<br><br>✅ Ahli Visa (transferable locally)<br><br>✅ Candidates must be locally available in Kuwait<br><br>✅ Immediate joiners only<br><br>???? Contact: 90913685 (Whatsapp)<br><br>Interested candidates, please share your CV on Whats App.<br><br>Kuwaitjob listings<br><br>Basic Details<br><br>Location : Shuaiba , Kuwait<br><br>Qualification : Diploma or Bachelors<br><br>Posted : 16 days ago<br><br>Job Type : Full-Time<br><br>Company : KDF<br><br>Posted By: TARANPREET KAUR<br><br>Contact Info<br><br>Mobile : +965 90913685<br><br>Alternate Mobile : Not-Mentioned<br><br>Email : Not-Mentioned

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <span>Long Description <br><br>Job Summary <br></span><p>Electronic service technicians are responsible for diagnosing, repairing or replacing parts for all household appliances.</p><br> <br><br>Job Responsibilities <br><ul> <li>Prescreen, identify, analyze, and repair appliance and electronic product failures ensuring customer satisfaction.</li> <li>Configuring/troubleshooting experience with hardware including audio-DSP, A/V control, video and audio devices, and USB based software applications.</li> <li>Order necessary parts after initial prescreen so they are in hand before going to customers' location.</li> <li>Perform daily administrative functions to include warranty claims and report submission.</li> <li>Maintain performance objectives as required by the company.</li> <li>Maintain company vehicle, tools, equipment and parts inventory.</li> <li>Rely on personal judgment for safety regarding work.</li> <li>Work independently without onsite supervision.</li> <li>Other duties as assigned.</li> <li>Documents service and installation actions by completing forms, reports, logs, and records.</li> </ul> <br><br>Candidate Requirements <br><ul> <li>3 to 5 years field service experience in all major home appliances.</li> <li>Possess appropriate Refrigerant Handling Certificate(s), CET, (HVAC) and other applicable appliance or electronics service certifications.</li> <li>Knowledge and proficient use of electronic and appliance and/or refrigeration tools and diagnostic test equipment.</li> <li>Proficient in MS Office and Smartphone technology with the ability to quickly learn proprietary software applications.</li> <li>Valid driver's license with a clear driving record.</li> <li>Meet physical requirements generally associated with field service repair (lifting, bending, etc.).</li> <li>Ability to work a flexible schedule based on business needs.</li> <li>Excellent communication, organization and customer service&nbsp;skills.</li> </ul> <br><br>Education <br><br><br> </div>

FABRICATORS<br><br> Job Id :100193888<br><br>Hire Resume Writers<br><br>×<br><br>Please enter details to report job<br><br>Name*<br><br>Email*<br><br>Reason to report<br><br>Description<br><br>Apex Group Intl. GTC is looking for below mentioned category of employees for immediate recruitment; 01. QA/QC Engineers with KOC approval 02. Welding Inspectors with KOC approval 03. Mechanical Engineers with KOC approval 04. Downhill welders 05. Fabricators (Flow Line) 06. Fitters 07. Helpers Interested candidates may send in their C. V's to sim#6 or e-mail us to ''.<br><br>Basic Details<br><br>Qualification<br><br>Posted : 28 days ago<br><br>Job Type : Full-Time<br><br>Company : Kuwait Jobs<br><br>Posted By: Saikumar<br><br>The current job you are viewing is either old or expired<br><br>Kindly look at the latest jobs<br><br>For the related jobs check below<br><br>Hire Resume Writers

We are urgently hiring for the following positions in Kuwait:<br><br> Cleaner <br><br> Job Id :100193951<br><br>Jobs<br><br>×<br><br>Please enter details to report job<br><br>Name*<br><br>Email*<br><br>Reason to report<br><br>Description<br><br>We are urgently hiring for the following positions in Kuwait:<br><br> *Cleaners kitchen dishwasher,*<br><br>*Duty time 9 am To 6 pm*<br><br>Salary 150 KD + 50 KD Allowance for Accommodation and transport<br><br>Food in duty time free*<br><br> *Line Cook / Commis*<br><br>Industry: Multi-Cuisine Restaurant<br><br> *Salary: 230 +50 for Accommodation transport total 280 KWD* *Food free in duty time* No Accommodation No Transportation<br><br>Requirements:<br><br> Immediate joiners only *Waiter / Waiteres*<br><br>Industry: Multi-Cuisine Restaurant<br><br> *Salary: 180 + 50 allowance for accommodation and transport and Total 230 KWD* *Food free available* No Accommodation No Transportation<br><br>Requirements:<br><br> Immediate joiners only<br><br>???? How to Apply<br><br>Whats App (CV Only – No Direct Calls):<br><br> +965 6550 5929<br><br>Email: hrdsrts@yahoo.com<br><br>Only shortlisted candidates will be contacted.<br><br>Recruitment& Staffing<br><br>Basic Details<br><br>Location : Fahaheel , Kuwait<br><br>Qualification : <br><br>Posted : 26 days ago<br><br>Job Type : Full-Time<br><br>Company : Kuwait Jobs<br><br>Contact Info<br><br>Mobile : +965 65505929<br><br>Alternate Mobile : Not-Mentioned<br><br>Email : Not-Mentioned

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><b>Electrician Oil &amp; Gas Shutdown</b></p><p><br></p><p>Certified industrial electricians for a 4-month shutdown project. H2S and safety certification mandatory. Attractive project completion bonus.</p><p><br></p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p><br></p><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p>Roles &amp; Responsibilities:</p><p>Inspect, diagnose, repair, and maintain reefer containers.</p><p>Perform preventive and corrective maintenance on refrigeration systems.</p><p>Troubleshoot electrical, mechanical, and refrigeration faults.</p><p>Handle units from leading brands such as Carrier, Thermo King, Daikin, Star Cool, and similar.</p><p>Prepare maintenance reports and update service records using MS Excel.</p><p>Ensure equipment operates efficiently and complies with safety standards.</p><p>Requirements:</p><p>ITI / Diploma in Refrigeration, Air Conditioning, Mechanical, or a related field.</p><p>Experience working on reefer containers is mandatory.</p><p>Hands-on experience with Carrier, Thermo King, Daikin, Star Cool, or similar reefer units.</p><p>Proficiency in MS Excel for reporting and documentation.</p><p>Good English communication skills.</p><p>GCC experience is preferred.</p><p>Benefits:</p><p>Accommodation provided</p><p>Transportation provided</p><p>Online Interview</p><p>Attractive salary package</p><p>Specialism: Refrigeration &amp; Cold Chain / Container Maintenance</p><p>Job Types: Full-Time</p><p>Location: Kuwait</p><p>Duty Hours: 9(8+1) Hrs / 6 Days</p><p>Duty Days: 6 Days</p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li>ITI / Diploma in Refrigeration, Air Conditioning, Mechanical, or a related field.</li><li>Experience working on reefer containers is mandatory.</li><li>Hands-on experience with Carrier, Thermo King, Daikin, Star Cool , or similar reefer units.</li><li>Proficiency in MS Excel for reporting and documentation.</li><li>Good English communication skills.</li><li>GCC experience is preferred.</li></ul><p></p></section>

<p>The Mechanical Metrology Engineer is the resident expert in his field and, in conjunction with the Kuwait Senior Engineer, provides engineering/consultant services to the GOK. Conducts research and studies new equipment to ensure that the latest developments in technique and equipment are included in metrology planning for future acquisition. Assists in the development and implementation of a Metrology QA Program as required. Assists in obtaining and maintaining laboratory QA accreditation. Assesses requirements and develops new measurement techniques and approaches related to mechanical, electro- mechanical, optical, electro-optical, chemical, and electro-chemical calibration methodology. Also performs analysis and evaluation of equipment test and performance requirements, and prescribes calibration approaches, test equipment and servicing requirements necessary to assure measurement traceability. Directs, conducts and evaluates the development of calibration procedures for assigned equipment categories. Conducts liaison and coordinates with technical societies and engineering facilities of other countries to remain current with the state-of-the-art and new measurement techniques. Responsible for laboratory facility and related environmental control development, operation and maintenance. Coordinates with civilian contractor and military civil engineering organizations on all projects affecting metrology facilities to ensure timely completion. Acts as consultant to GOK military and ministries on matters pertaining to metrology facilities and environmental requirements. Conducts liaison and coordination with technical societies and engineering facilities of other countries to remain current with state-of-the-art for metrology facilities and environmental control systems. Works with the Electrical Engineer on all matters associated with Power Production and Facilities. It is anticipated that Engineers will be assigned as these job descriptions state and other related specific tasking details and priorities will be determined and set by the Commander, KAFMB and communicated to the Contractor lead.</p><p><strong>Desired Candidate Profile</strong></p><p>An Associate s degree in mechanical engineering, physics or a related technical field from an accredited college or university and twelve (12) years of work experience operating, maintaining, troubleshooting, repairing, calibrating electronic precision measurement equipment and calibration laboratory reference standards. Includes qualification requirements D and E. OR; Completion of a U.S. military precision measurement and calibration school and twelve (12) years of work experience in the metrology and calibration field. Completion of a precision measurement and calibration school at an accredited school, or within a specialized calibration firm, and twelve (12) years of experience operating, maintaining, troubleshooting, repairing and calibrating physical/dimensional precision measurement equipment and calibration laboratory reference standards. I Five (5) years of experience in technical oversight and training responsibilities of calibration and repair technicians with three (3) years within the last five (5) years. Experience in researching requirements and maintaining calibration laboratory facility and related environmental control systems. Must have an Active Secret US Government Clearance. US Citizenship is required to obtain a Secret Clearance.</p>

<p>The Mechanical Metrology Engineer is the resident expert in his field and, in conjunction with the Kuwait Senior Engineer, provides engineering/consultant services to the GOK. Conducts research and studies new equipment to ensure that the latest developments in technique and equipment are included in metrology planning for future acquisition. Assists in the development and implementation of a Metrology QA Program as required. Assists in obtaining and maintaining laboratory QA accreditation. Assesses requirements and develops new measurement techniques and approaches related to mechanical, electro- mechanical, optical, electro-optical, chemical, and electro-chemical calibration methodology. Also performs analysis and evaluation of equipment test and performance requirements, and prescribes calibration approaches, test equipment and servicing requirements necessary to assure measurement traceability. Directs, conducts and evaluates the development of calibration procedures for assigned equipment categories. Conducts liaison and coordinates with technical societies and engineering facilities of other countries to remain current with the state-of-the-art and new measurement techniques. Responsible for laboratory facility and related environmental control development, operation and maintenance. Coordinates with civilian contractor and military civil engineering organizations on all projects affecting metrology facilities to ensure timely completion. Acts as consultant to GOK military and ministries on matters pertaining to metrology facilities and environmental requirements. Conducts liaison and coordination with technical societies and engineering facilities of other countries to remain current with state-of-the-art for metrology facilities and environmental control systems. Works with the Electrical Engineer on all matters associated with Power Production and Facilities. It is anticipated that Engineers will be assigned as these job descriptions state and other related specific tasking details and priorities will be determined and set by the Commander, KAFMB and communicated to the Contractor lead.</p><p><strong>Desired Candidate Profile</strong></p><ul><li>An Associate's degree in mechanical engineering, physics or a related technical field from an accredited college or university and twelve (12) years of work experience operating, maintaining, troubleshooting, repairing, calibrating electronic precision measurement equipment and calibration laboratory reference standards. Includes qualification requirements D and E.</li><li>OR; Completion of a U.S. military precision measurement and calibration school and twelve (12) years of work experience in the metrology and calibration field.</li><li>Completion of a precision measurement and calibration school at an accredited school, or within a specialized calibration firm, and twelve (12) years of experience operating, maintaining, troubleshooting, repairing and calibrating physical/dimensional precision measurement equipment and calibration laboratory reference standards.</li><li>I Five (5) years of experience in technical oversight and training responsibilities of calibration and repair technicians with three (3) years within the last five (5) years.</li><li>Experience in researching requirements and maintaining calibration laboratory facility and related environmental control systems.</li><li>Must have an Active Secret US Government Clearance.</li><li>US Citizenship is required to obtain a Secret Clearance.</li></ul>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p>As a Technical Support Engineer for our Digital Solutions Platform, you will play a critical role in ensuring our clients receive top-notch support and solutions tailored to their needs. This position is not just about troubleshooting; it’s about building relationships and providing insights that help our clients maximize the value of our digital solutions. You will be part of a dynamic team where innovation meets customer service, and every day brings new challenges and opportunities to learn.</p><p>In this role, you will have the chance to engage with cutting-edge technologies and collaborate with cross-functional teams to deliver solutions that truly make a difference. We believe in investing in our employees’ growth; therefore, you will have access to continuous training and development opportunities. This is an exciting time to join our company as we expand our digital offerings, and your contributions will be pivotal in shaping the future of our services.</p><p>We foster a culture of teamwork, respect, and open communication, where every team member’s input is valued. You will be encouraged to share your ideas and be part of a collaborative environment that prioritizes innovation. As you grow in this role, you will have the opportunity to take on more significant responsibilities and advance your career within the organization, making this a perfect opportunity for those looking to build a long-term career in tech support.</p><p><b>Responsibilities:</b></p><ol><li>Provide exceptional technical support to clients, addressing inquiries and troubleshooting issues through various communication channels, ensuring a prompt and effective resolution.</li><li>Utilize diagnostic tools and software to analyze client problems and recommend solutions, enhancing the user experience and maintaining customer satisfaction.</li><li>Document and track all client interactions and technical issues in the support ticketing system, contributing to knowledge management and process improvement.</li><li>Collaborate with product development teams to relay customer feedback and suggest enhancements, ensuring our digital solutions remain competitive and user-friendly.</li><li>Conduct training sessions and workshops for clients on the use of our digital platforms, empowering them to utilize the tools effectively and independently.</li><li>Participate in the development of user manuals and documentation, ensuring that technical information is accessible and clear for end-users.</li><li>Monitor system performance and client usage metrics, proactively identifying potential issues and implementing solutions before they escalate.</li><li>Assist in the onboarding process for new clients, providing them with the necessary resources and support to ensure a smooth transition.</li><li>Stay updated with industry trends and emerging technologies, continuously enhancing your skills and knowledge to provide cutting-edge support.</li></ol> </div><h2 class="h5">Skills</h2> <div data-jb-field="skills"><p><b>Key Requirements:</b></p><ul><li>3–5 years of technical support experience for enterprise software or digital platforms.</li><li>Strong troubleshooting and problem-solving capabilities.</li><li>Experience supporting APIs, integrations, web applications, and cloud-based platforms is an advantage.</li><li>Good understanding of SQL, databases, and system configurations.</li><li>Excellent customer service and communication skills.</li></ul><p><br></p></div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Scope of work:</b></p><p>Technical Support Engineer is responsible for providing technical assistance, troubleshooting hardware and software issues, and ensuring the smooth operation of IT systems and end-user support.</p><p><br></p><p><b>Key Responsibilities:</b></p><ul><li>Provide technical support and services for ID Card Printers.</li><li>Provide first and second-level technical support for hardware, software, and network-related issues.</li><li>Install, configure, and maintain desktop computers, laptops, printers, scanners, and other IT peripherals.</li><li>Install, configure, and troubleshoot operating systems, applications, and business software.</li><li>Respond to user support requests via phone, email, ticketing systems, or in person within agreed service levels.</li><li>Diagnose and resolve hardware, software, network, and connectivity issues.</li><li>Configure and maintain user accounts, email accounts, and access permissions.</li><li>Monitor system performance and ensure the availability of IT infrastructure.</li><li>Perform preventive maintenance, system updates, and software patch installations.</li><li>Escalate complex technical issues to senior engineers or vendors when necessary.</li><li>Maintain accurate records of incidents, service requests, and resolutions in the helpdesk system.</li><li>Support LAN/WAN connectivity, Wi-Fi networks, VPN access, and basic network troubleshooting.</li><li>Assist in the deployment of new hardware, software, and IT infrastructure projects.</li><li>Ensure compliance with IT security policies, antivirus protection, and data backup procedures.</li><li>Provide user training and guidance on IT systems, software applications, and cybersecurity best practices.</li><li>Coordinate with vendors for equipment repairs, warranty claims, and technical support.</li><li>Prepare technical documentation, user manuals, and system configuration records.</li><li>Participate in disaster recovery and business continuity activities as required.</li><li>Perform any other IT support duties assigned by the IT Manager or management</li></ul> </div><h2 class="h5">Skills</h2> <div data-jb-field="skills"><p><b>Education:</b></p><ul><li>Bachelor’s degree in IT/ Computer Science / Engineering&nbsp;</li></ul><p><br></p><p><b>Qualifications and Skills:</b></p><ul><li>Knowledge of Windows operating systems, Microsoft 365, Active Directory, networking, and troubleshooting hardware. </li><li>Familiarity with ticketing systems and remote support tools. </li><li>Strong analytical, problem-solving, and communication skills. </li><li>Ability to work independently and provide excellent customer service</li><li>Bachelor’s degree in IT/ Computer Science / Engineering </li><li>Must be a certified engineer from the submitted ID card printer manufacturer.</li><li>CCNP certificate.</li><li>Certified in servers' administration.</li></ul><p><br></p><p><b>Experience:</b></p><ul><li>3–5 years of experience in technical support or IT helpdesk operations. </li><li>Must have a minimum of 5 years' experience in ID card Printers Hardware &amp; software Deployment &amp; Maintenance.</li></ul><p><br></p></div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Company Description<br><p>Al Jazeera Real Estate Development Co. K.S.C.C (AJRE) founded in 2002, is a closed shareholding Company has an impressive 22-years of track record providing high-quality developments such as Sahara Kuwait Golf Resort, Murouj Mall &amp; Sahara Equestrian Resort.</p><br><p>AJRE continues to develop its business by expanding into related business lines and offering new products and services. AJRE is committed to the pursuit of excellence and will continue evaluating ways to strengthen policies and practices to promote the interests of shareholders, partners, and employees.</p><br><br>Job Description<br><p>Sahara Arena is seeking a Technical Assistant to support the Operations Manager in the daily technical operation and maintenance of the venue. The successful candidate will help ensure the arena is safe, event-ready, and operating efficiently by coordinating maintenance activities, reviewing technical event requirements, and providing technical support before, during, and after events – to a standard consistent with comparable local and regional arenas.</p><br><br>Qualifications<br><ul><li>Diploma or Bachelor’s degree in Engineering (Mechanical, Electrical, or related) or a related technical field.</li><li>2+ years’ experience in arenas, theatres, exhibition halls, stadiums, or live event production preferred.</li><li>Strong working knowledge of entertainment rigging, trusses, chain hoists/motors (including large-capacity grids), AV systems, professional sound and lighting, LED screens, and electrical power distribution/generators.</li><li>Ability to read and interpret technical drawings, rigging plans, load calculations, and event layouts.</li><li>Recognized rigging/safety certification (e.g., ETCP Rigger, IRATA, or equivalent), or willingness to obtain one, is an advantage.</li><li>Familiarity with CMMS or maintenance-tracking software for PPM and asset management.</li><li>Proficiency in Microsoft Office; AutoCAD or Vectorworks knowledge is a strong advantage.</li><li>Strong communication, organizational, and problem-solving skills, with the ability to stay calm under the time pressure of live event load-in/load-out.</li><li>Willingness to work flexible hours – including evenings, weekends, and public holidays – based on event schedules, and to provide on-call standby coverage during live shows.</li></ul><br>Additional Information<br><p><strong>Venue Operations &amp; Preventive Maintenance</strong></p><br><ul><li>Assist in the daily technical operation of the arena, including mechanical, electrical, fire/life-safety, rigging and AV systems.</li><li>Perform routine inspections and Preventive Planned Maintenance (PPM), logging all activity in the venue’s CMMS or maintenance-tracking system.</li><li>Coordinate maintenance team and supervise contractors and specialist vendors, verifying completed work meets venue and manufacturer standards.</li><li>Maintain accurate maintenance records, asset registers, and technical documentation (as-built drawings, rigging certificates, equipment manuals).</li><li>Ensure all building systems and event infrastructure – including the rigging grid up to its full rated capacity, power distribution, HVAC, and LED/AV systems – operate safely and efficiently.</li></ul><p><strong>Event Technical Support</strong></p><br><ul><li>Attend technical meetings and advance calls with event organizers, touring production teams, and contractors.</li><li>Review and validate incoming technical riders, stage plots, and rigging plans against venue capacities before approving load-ins.</li><li>Provide hands-on technical support during event setup, rehearsals, live events, and dismantling, including standby coverage for live shows.</li></ul><p><strong>Pre- &amp; Post-Event Responsibilities</strong></p><br><ul><li>Before each event: review technical submissions, verify rigging and roof/grid loads against certified limits, inspect hoists, trusses, chain motors, power distribution boards/generators and AV systems, and confirm the arena is fully event-ready.</li><li>After each event: inspect the venue and equipment for damage or faults, document maintenance requirements, coordinate necessary repairs with contractors, and ensure the arena is restored and ready for the next event.</li></ul><p><strong>Health, Safety &amp; Compliance</strong></p><br><ul><li>Support compliance with Kuwait Civil Defence, fire/life-safety, and recognized international rigging and entertainment-industry safety standards.</li></ul><br><br> </div>

<p><h4>Job Description</h4> <p>The Mechanical Metrology Engineer is the resident expert in his field and, in conjunction with the Kuwait Senior Engineer, provides engineering and consultant services to the GOK. Conducts research and studies new equipment to ensure that the latest developments in technique and equipment are included in metrology planning for future acquisition. Assists in the development and implementation of a Metrology QA Program as required. Assists in obtaining and maintaining laboratory QA accreditation.</p> <p>Assesses requirements and develops new measurement techniques and approaches related to mechanical, electro-mechanical, optical, electro-optical, chemical, and electro-chemical calibration methodology. Also performs analysis and evaluation of equipment test and performance requirements, and prescribes calibration approaches, test equipment, and servicing requirements necessary to assure measurement traceability. Directs, conducts, and evaluates the development of calibration procedures for assigned equipment categories. Conducts liaison and coordinates with technical societies and engineering facilities of other countries to remain current with the state-of-the-art and new measurement techniques.</p> <p>Responsible for laboratory facility and related environmental control development, operation, and maintenance. Coordinates with civilian contractor and military civil engineering organizations on all projects affecting metrology facilities to ensure timely completion. Acts as consultant to GOK military and ministries on matters pertaining to metrology facilities and environmental requirements. Conducts liaison and coordination with technical societies and engineering facilities of other countries to remain current with state-of-the-art for metrology facilities and environmental control systems. Works with the Electrical Engineer on all matters associated with power production and facilities.</p> <p>It is anticipated that engineers will be assigned as these job descriptions state and other related specific tasking details and priorities will be determined and set by the Commander, KAFMB and communicated to the contractor lead.</p> <h4>Qualifications</h4> <ul> <li>An associate’s degree in mechanical engineering, physics, or a related technical field from an accredited college or university and twelve (12) years of work experience operating, maintaining, troubleshooting, repairing, calibrating electronic precision measurement equipment and calibration laboratory reference standards. Includes qualification requirements D and E. OR;</li> <li>Completion of a U.S. military precision measurement and calibration school and twelve (12) years of work experience in the metrology and calibration field.</li> <li>Completion of a precision measurement and calibration school at an accredited school, or within a specialized calibration firm, and twelve (12) years of experience operating, maintaining, troubleshooting, repairing, and calibrating physical/dimensional precision measurement equipment and calibration laboratory reference standards.</li> <li>Five (5) years of experience in technical oversight and training responsibilities of calibration and repair technicians with three (3) years within the last five (5) years.</li> <li>Experience in researching requirements and maintaining calibration laboratory facility and related environmental control systems.</li> <li>Must have an active secret US government clearance.</li> <li>US citizenship is required to obtain a secret clearance.</li> </ul></p><p></p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Skills and Behavioral Competencies</b></p><p><b>Communication:</b></p><ul><li>Ability to communicate effectively verbally and in writing.</li><li>Effective communication with others (co-workers, supervisors, and other departments) through providing and exchanging information.</li></ul><p><b>Professional Abilities and Skills:</b></p><ul><li>Familiarity with safety and quality standards.</li><li>Good knowledge of production processes and food safety.</li><li>Optimal interaction with company members and mastering work while preserving company property and its secrets.</li><li>Ability to work under pressure.</li><li>Good knowledge of mechanical systems and components.</li><li>Ability to use mechanical tools, equipment, and instruments.</li><li>Ability to conduct technical analyses.</li></ul><p><b>Languages:</b></p><p>• Ability to communicate in Arabic or English, at least at a conversational level.</p><p><b>Personal Skills:</b></p><ul><li>Flexibility in work.</li><li>Responsibility and building trust with others.</li><li>Teamwork skills.</li><li>Knowledge of labor laws.</li><li>Punctuality.</li><li>Accuracy and focus.</li><li>Job competencies.</li><li>Required competency rating.</li></ul><p><br></p><p><b>Tasks and Responsibilities</b></p><ul><li>Inspect machinery and equipment according to maintenance plans established by management.</li><li>Clean machinery, equipment, and work areas and follow all instructions issued by the direct supervisor.</li><li>Prepare the required tools, equipment, materials, and instruments for inspection, maintenance, and repair activities.</li><li>Conduct routine inspections and preventive maintenance of mechanical machinery and equipment.</li><li>Coordinate with the direct supervisor to ensure the availability of required spare parts.</li><li>Apply all workplace health and safety principles and procedures during maintenance activities.</li><li>Coordinate with other maintenance teams involved in maintenance and repair activities.</li><li>Perform maintenance and repairs on mechanical machinery and equipment according to the instructions of the direct supervisor.</li><li>Assist with the installation and commissioning of new mechanical equipment.</li><li>Prepare technical reports on the condition and performance of mechanical equipment.</li><li>Train and guide junior workers on basic mechanical maintenance activities.</li><li>Participate in developing and improving preventive maintenance plans for mechanical equipment.</li><li>Maintain professional ethics and prioritize the company's interests in all activities.</li><li>Perform any other duties within the scope of the position as assigned by the supervisor.</li></ul><p><b>Required Skills &amp; Competencies</b></p><ul><li>Good knowledge of mechanical equipment systems and components.</li><li>Ability to use mechanical tools, equipment, and instruments.</li><li>Ability to perform basic technical analysis and identify mechanical issues.</li><li>Good understanding of production processes and food safety requirements.</li><li>Knowledge of workplace safety and quality standards.</li><li>Ability to work effectively under pressure.</li><li>Strong attention to detail and accuracy.</li><li>Good teamwork and communication skills.</li><li>Flexible and responsible approach to work.</li><li>Punctual, reliable, and accountable.</li><li>Ability to maintain company property and confidentiality.</li><li>Good interpersonal and professional skills.</li></ul><p>Language Requirements</p><ul><li>Ability to communicate in <b>Arabic or English</b>, at least at a conversational level.</li></ul><p><b>Qualifications:</b></p><ul><li>Technical Diploma in Mechanics or equivalent.</li><li>High School Diploma with practical experience.</li></ul><p><b>Experience:</b></p><ul><li>Fresh Graduate.</li><li>3 years experience.</li></ul><p><br></p> </div><h2 class="h5">Skills</h2> <div data-jb-field="skills"><p>Job Summary</p><p>Responsible for inspecting, maintaining, troubleshooting, and repairing mechanical equipment and machinery to ensure safe, reliable, and efficient operation. The role supports preventive maintenance activities, equipment installation, technical analysis, spare parts coordination, and compliance with safety and quality standards.</p><p>Key Responsibilities</p><ul><li>Inspect machinery and equipment according to maintenance plans established by management.</li><li>Clean machinery, equipment, and work areas and follow all instructions issued by the direct supervisor.</li><li>Prepare the required tools, equipment, materials, and instruments for inspection, maintenance, and repair activities.</li><li>Conduct routine inspections and preventive maintenance of mechanical machinery and equipment.</li><li>Coordinate with the direct supervisor to ensure the availability of required spare parts.</li><li>Apply all workplace health and safety principles and procedures during maintenance activities.</li><li>Coordinate with other maintenance teams involved in maintenance and repair activities.</li><li>Perform maintenance and repairs on mechanical machinery and equipment according to the instructions of the direct supervisor.</li><li>Assist with the installation and commissioning of new mechanical equipment.</li><li>Prepare technical reports on the condition and performance of mechanical equipment.</li><li>Train and guide junior workers on basic mechanical maintenance activities.</li><li>Participate in developing and improving preventive maintenance plans for mechanical equipment.</li><li>Maintain professional ethics and prioritize the company's interests in all activities.</li><li>Perform any other duties within the scope of the position as assigned by the supervisor.</li></ul><p>Required Skills &amp; Competencies</p><ul><li>Good knowledge of mechanical equipment systems and components.</li><li>Ability to use mechanical tools, equipment, and instruments.</li><li>Ability to perform basic technical analysis and identify mechanical issues.</li><li>Good understanding of production processes and food safety requirements.</li><li>Knowledge of workplace safety and quality standards.</li><li>Ability to work effectively under pressure.</li><li>Strong attention to detail and accuracy.</li><li>Good teamwork and communication skills.</li><li>Flexible and responsible approach to work.</li><li>Punctual, reliable, and accountable.</li><li>Ability to maintain company property and confidentiality.</li><li>Good interpersonal and professional skills.</li></ul><p>Language Requirements</p><ul><li>Ability to communicate in <b>Arabic or English</b>, at least at a conversational level.</li></ul><p><b>Qualifications:</b></p><ul><li>Technical Diploma in Mechanics or equivalent.</li><li>High School Diploma with practical experience.</li></ul><p><b>Experience:</b></p><ul><li>Fresh Graduate.</li><li>3 years experience.</li></ul><p><br></p></div>

<p>Operation and Maintenance (O&amp;M) of the Digital Small Switch DSS-2A Monitor trunk and circuit outages as well as the administrative terminal and Enhanced Command Console (ECC). Perform direct trunk dialing checks over trunk channels associated with the switch to ensure satisfactory operation of voice circuits (at least once each shift and following any trunk failure). Perform Preventive Maintenance Inspections (PMIs) on the switch and peripheral equipment. Conduct systems checks every 2 hours. Create and update databases in the administrative terminal using information received from users, Raytheon, and DISA. Perform database backups to CD-R discs. Perform database downloads to update switch configurations. Update and print out telephone console information and line strips for users. Fabricate custom interface cables using hand tools and wiring diagrams. Escort individuals requiring access to the Red Switch in the performance of their duties. Ensure that all outages are reported in a timely manner to the DISA GNOSC, NOC-K, TCF, V2X management for tracking in Army Enterprise Service Management Platform (AESMP) ticketing system. Provide hourly status updates to designated agencies regarding outages, etc. Annotate all activities in the Master Station Log (MSL) database. Prepare call detail history reports for DISA and military personnel as directed. Contribute to weekly reports with regard to your additional duties and other assigned tasks. Complete individual timesheets on a daily basis. Check the Regional Cyber Center (RCC) website for accuracy regarding authorized service interruptions (ASIs) and outages. Initiate Quality Control checklists as they pertain to your additional duties. Update training records as needed. Update memorandums and technical drawings (including block diagrams and schematics) as directed. Inventory Communications Security (COMSEC) equipment and document DA Form 2653-R (each shift). Work with military technical monitor(s), Special Security Office (SSO) and other Department of Defense contractors and civilians including local hires in support of the DRSN mission. Interface with technicians from Outside Plant, DPW, FMO etc. regarding installations in support of the DRSN mission. Coordinate with the Raytheon Help Desk for troubleshooting problems that cannot be resolved locally. Contact the Return Merchandise Authorization (RMA) Help Desk in order to obtain an RMA for processing Depot equipment repairs. Performs other duties and assignments as required.</p><p><strong>Desired Candidate Profile</strong></p><ul><li>Active Top Secret SSBI within the past two years.</li><li>Individual must be eligible for Sensitive Compartmentalized Information (SCI) Access.</li><li>High School Diploma required.</li><li>Bachelor s Degree in IT or related field preferred.</li><li>Cardiopulmonary Resuscitation (CPR) ( Provided by contract )</li><li>One year of related academic study above the high school level may be substituted for one year of experience up to a maximum of a 4-year bachelor's degree.</li><li>Seven years experience in Communications-Electronics Maintenance functions: installation, troubleshooting and repair of electronic communications equipment.</li><li>Use of phone Digital sender, and desktop computer in a fast-paced office environment is desirable.</li><li>A working knowledge of Microsoft Office software is required.</li><li>Must be able to work rotating shift schedules which provide 24-hour day/7-day week coverage.</li><li>Military or civilian technical training course of six (6) months or more is required.</li><li>This should be followed by a minimum of 24 months of on-the-job training (OJT).</li><li>A certificate of completion will suffice until verification of the training on your DD-214 can be completed.</li><li>Experience with a customer service-oriented company</li></ul>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><br></p><p><b>Responsibilities:</b></p><ol><li>Operate and maintain advanced laser equipment for various dermatological procedures, ensuring compliance with safety protocols and standards to deliver effective treatment outcomes.</li><li>Conduct thorough patient assessments to determine the suitability of laser treatments, utilizing your expertise to recommend appropriate procedures based on individual needs.</li><li>Monitor and document patient progress throughout the treatment process, using electronic health records to track outcomes and communicate findings to the healthcare team.</li><li>Provide pre-treatment consultations to educate patients about the procedures, potential risks, and expected results, fostering a trusting relationship and enhancing patient satisfaction.</li><li>Collaborate with dermatologists and other medical professionals to develop personalized treatment plans that align with the latest advancements in dermatological care.</li><li>Stay updated on industry trends and technological advancements in laser treatments, participating in ongoing training to enhance your skills and knowledge.</li><li>Ensure a clean and safe working environment by adhering to infection control protocols and maintaining equipment in optimal condition to prevent complications.</li><li>Assist in marketing initiatives by sharing success stories and patient testimonials, contributing to the growth of the practice and enhancing its reputation in the community.</li><li>Participate in team meetings and training sessions, sharing insights and experiences to promote a culture of continuous improvement and professional development.</li></ol> </div><h2 class="h5">Skills</h2> <div data-jb-field="skills"><ul><li>Proficient in operating various laser technologies used in dermatology, ensuring optimal treatment delivery.</li><li>Strong understanding of dermatological conditions and treatment protocols to provide informed patient care.</li><li>Excellent communication skills to effectively educate patients and collaborate with medical staff.</li><li>Detail-oriented with strong organizational skills to manage patient records and treatment documentation accurately.</li><li>Ability to work in a fast-paced environment while maintaining a high level of patient care and safety.</li><li>Commitment to continuous learning and professional development in the field of dermatology.</li><li>Team player with a positive attitude, contributing to a supportive and collaborative work culture.</li></ul></div>

Additional Information<br><br>Job Number 26115032<br><br>Job Category Engineering & Facilities<br><br>Location Abdel Moneim Ryadh Street, Kuwait City, Kuwait, Kuwait, 26302VIEW ON MAP<br><br>Schedule Full Time<br><br>Located Remotely? N<br><br>Position Type Non-Management<br><br>Position Summary<br><br>Inspect, repair, and maintain HVAC, air quality control, and refrigeration equipment. Maintain and conduct daily inspections of the mechanical plant. Monitor and control property temperature. Monitor and analyze energy and utilities usage. Calibrate all controls, gauges, meters, and other equipment. Assemble, install, test, repair, and maintain electrical systems or electronic wiring. Assemble, install, and maintain pipe assemblies, fittings, valves, etc. Perform routine pool and spa maintenance.<br><br>Follow all company and safety and security policies and procedures; report maintenance problems, safety hazards, accidents, or injuries; and complete safety training and certifications. Ensure uniform and personal appearance are clean and professional, maintain confidentiality of proprietary information, and protect company assets. Welcome and acknowledge all guests according to company standards and anticipate and address guests’ service needs. Speak with others using clear and professional language. Develop and maintain positive working relationships with others and listen and respond appropriately to the concerns of other employees. Ensure adherence to quality expectations and standards; and identify, recommend, develop, and implement new ways to increase organizational efficiency, productivity, quality, safety, and/or cost-savings. Reach overhead and below the knees. Move in confined or elevated spaces. Move over sloping, uneven, or slippery surfaces. Move up and down stairs, service ramps and/or a ladder. Grasp, turn, and manipulate objects of varying size and weight. Assist with moving, lifting, carrying, and placing of objects weighing in excess of 100 pounds. Move, lift, carry, push, pull, and place objects weighing less than or equal to 50 pounds without assistance. Perform other reasonable job duties as requested by Supervisors.<br><br>Preferred Qualifications<br><br>Education: Technical, Trade, or Vocational School Degree.<br><br>Related Work Experience: At least 3 years of related work experience.<br><br>Supervisory Experience: No supervisory experience.<br><br>Required Qualifications<br><br>License or Certification: EPA Universal Certification<br><br>Driver's License<br><br>HVAC Certification<br><br>At Marriott International, we are dedicated to being an equal opportunity employer, welcoming all and providing access to opportunity. We actively foster an environment where the unique backgrounds of our associates are valued and celebrated. Our greatest strength lies in the rich blend of culture, talent, and experiences of our associates. We are committed to non-discrimination on any protected basis, including disability, veteran status, or other basis protected by applicable law.<br><br>The world is a big place and Marriott Executive Apartments offers temporary housing that feels like home in the biggest and best cities for business travel across Europe, Asia, Latin America, Africa and the Middle East. Join the Marriott Executive Apartments team and help our guests adapt to a new locale and feel comfortable and cared for while living away from home. In joining Marriott Executive Apartments, you join a portfolio of brands with Marriott International. Be where you can do your best work, begin your purpose, belong to an amazing global team, and become the best version of you.

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p>Provide technical expertise on fire engines, rescue vehicles, airport rescue and firefighting (ARFF) vehicles, tankers, aerial platforms, and specialized firefighting vehicles.</p><p>Review and evaluate technical specifications, drawings, datasheets, and manufacturer documentation.</p><p>Support procurement activities by preparing technical specifications, evaluating vendor proposals, and participating in technical bid evaluations.</p><p>Ensure fire vehicles comply with applicable safety regulations, operational requirements, and recognized industry standards.</p><p>Recommend fleet upgrades, modifications, and equipment improvements to enhance operational capability.</p><p>Support emergency response operations by providing technical assistance when required.</p><p>Knowledge in:</p><ul><li>Fire vehicle construction and design</li><li>Fire pumps and water delivery systems</li><li>Foam proportioning systems</li><li>Hydraulic rescue equipment</li><li>Diesel engines and powertrains</li><li>Heavy vehicle electrical and electronic systems</li><li>Pneumatic and hydraulic systems</li><li>Vehicle diagnostics and troubleshooting</li><li>Preventive and corrective maintenance</li><li>Fleet management principles</li><li>Technical specifications and procurement</li><li>Inspection, testing, and commissioning of emergency vehicles</li><li>Occupational health and safety requirements</li><li>Emergency vehicle operational standards and best practices</li></ul><p>Skills:</p><ul><li>Strong technical and analytical skills</li><li>Ability to interpret engineering drawings and technical manuals</li><li>Inspection and quality assurance</li><li>Project coordination</li><li>Vendor and supplier coordination</li><li>Communication and presentation skills</li><li>Computer proficiency, including Microsoft Office and computerized maintenance management systems (CMMS)</li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Bachelor s degree in mechanical engineering, Automotive Engineering, Fire Protection Engineering, or a related engineering discipline.</p><p>Relevant professional experience in fire vehicle maintenance, emergency vehicle engineering, fleet management, or heavy vehicle maintenance.</p><p>Experience with municipal, industrial, military, or airport firefighting vehicles is preferred.</p><p></p></section>

Driver <br><br>Job Id :100195419<br><br>×<br><br>Please enter details to report job<br><br>Name*<br><br>Email*<br><br>Reason to report<br><br>Description<br><br>We are looking for experienced Generator / Diesel Mechanics with the following qualifications and responsibilities:<br><br>Key Responsibilities<br><br> Perform preventive and corrective maintenance on diesel generators of various capacities (e.g., 30 KVA to 2000 KVA). Perform inspection, servicing, maintenance, and repair of diesel-powered equipment and vehicles. Diagnose and repair mechanical, electrical, and control system faults. Conduct routine inspections, servicing, lubrication, and filter replacement. Repair and overhaul diesel engines, alternators, radiators, fuel systems, and cooling systems. Troubleshoot starting, charging, governor, and voltage regulation issues. Test generator performance under load and ensure stable voltage and frequency. Install, commission, and decommission generator sets. Maintain battery systems, chargers, control panels, and Automatic Transfer Switch (ATS) systems. Replace defective components including injectors, fuel pumps, turbochargers, belts, hoses, and sensors. Maintain accurate maintenance records, service reports, and spare parts inventory. Respond to emergency generator breakdowns and minimize equipment downtime. Ensure compliance with manufacturer specifications and safety procedures. Coordinate with operations teams to schedule maintenance activities. Maintain housekeeping standards in the workshop and at project sites.<br><br>Skills Required<br><br> Knowledge of diesel engines and alternators. Ability to read electrical and mechanical drawings. Experience with Perkins, Cummins, Caterpillar, FG Wilson, Atlas Copco, Volvo Penta, MTU, or similar generator brands. Familiarity with engine control modules (ECM) and diagnostic tools. Strong troubleshooting and fault-finding skills. Ability to work independently as well as part of a team. Ability to work independently and under pressure during emergency breakdowns. Commitment to workplace safety and preventive maintenance. Minimum 5-8 Years’ Experience and available valid Kuwaiti Driving License will be preferred. Candidate should be inside Kuwait and must have valid residency Visa 18 with Local transfer.<br><br>Job Types: Full-time, Permanent<br><br>Submit your CV to: mehndishah@sweetynational.com<br><br>Whats App: 66286604<br><br>Basic Details<br><br>Location : Fahaheel , Kuwait<br><br>Qualification<br><br>Posted : Today<br><br>Job Type : Full-Time<br><br>Company : Kuwait Jobs<br><br>Contact Info<br><br>Mobile : +965 66286604<br><br>Alternate Mobile : Not-Mentioned<br><br>Email : Not-Mentioned

Video Testimonial<br><br>Job Details<br><br>Department: 2nd Floor Rehab<br><br>Shift: Night<br><br>Working Hours: 630p to 700a<br><br>Summary:<br><br>The primary function of the PCT is to assist the patient and family with basic patient care, monitoring, hygiene, and to help ensure care is complete. The PCT works as an essential part of the patient care team. As the member who spends most of their time in the presence of the patient, compassion, caring, and excellent human interaction skills are necessary along with excellent communication skills both to and from the patient and family, and to and from the rest of the healthcare team.<br><br>Other Information:<br><br>12 college level credit hours that include a passing grade in English Composition with a C or higher and an overall GPA of 2.0 or greater. (transcripts will be verified upon application) Healthcare experience preferred but not required Service industry experience preferred but not required Willingness to work flexible hours Good organization skills Good verbal and written communication skills Ability to learn and apply new healthcare related skills Ability to communicate effectively and do so consistently Ability to collaborate with the health care team effectively and do so consistently Ability to engage people at the appropriate level for their wellness and cognition Ability to problem solve Ability to be proactive in anticipating the customer’s needs Will provide education that includes: CPR, Skills training, Crucial Conversations, and Hospitality in Healthcare<br><br>This job will be authorized 72.00 hours bi-weekly.<br><br>"><br><br>Department: 2nd Floor Rehab<br><br>Shift: Night<br><br>Working Hours: 630p to 700a<br><br>Other Information:<br><br>12 college level credit hours that include a passing grade in English Composition with a C or higher and an overall GPA of 2.0 or greater. (transcripts will be verified upon application) Healthcare experience preferred but not required Service industry experience preferred but not required Willingness to work flexible hours Good organization skills Good verbal and written communication skills Ability to learn and apply new healthcare related skills Ability to communicate effectively and do so consistently Ability to collaborate with the health care team effectively and do so consistently Ability to engage people at the appropriate level for their wellness and cognition Ability to problem solve Ability to be proactive in anticipating the customer’s needs Will provide education that includes: CPR, Skills training, Crucial Conversations, and Hospitality in Healthcare<br><br>This job will be authorized 72.00 hours bi-weekly.